Inheritance of wood properties and their radial variations in full-sib families of 36-year-old Japanese larch (Larix kaempferi (Lamb.) Carr.)

Larger differences of maximum load among families were found in mature wood compared to juvenile wood, suggesting the possibility of improving mature wood with higher resistance to rupture and maintaining characteristics of material in Larix kaempferi (Lamb.) Carr. by selecting specific mating parents. Because the wood from L. kaempferi trees is used for construction lumber, wood properties and bending properties should be focused on as targeted traits of tree breeding programs. We clarified the radial variation of inheritance for wood properties and bending properties and classified the features of bending properties among families in L. kaempferi. Annual ring width, latewood percentage, air-dry density, microfibril angle, modulus of elasticity, modulus of rupture, and bending work at five radial positions were investigated for 15 full-sib families of 36-year-old L. kaempferi grown in two progeny test sites in Japan. Higher heritability at almost all radial positions was found in air-dry density. Phenotypic and genetic correlations between air-dry density and bending properties showed relatively higher values at almost all radial positions. Load-deflection curves in 15 families could be divided into three groups in juvenile and mature wood. Variation among groups for load-deflection curves in mature wood was relatively larger than that in juvenile wood. Air-dry density can be used as a criterion to select trees with superior bending properties. Mature wood in L. kaempferi could be effectively improved by selecting individuals.


Introduction
Larix kaempferi (Lamb.) Carr. (karamatsu in Japanese and Japanese larch in English) is a deciduous conifer species that is naturally distributed in cold and high elevation areas in the central region of Honshu, Japan. It is one of the most major softwood plantation species in Japan (Takata et al. 2005). Plantations of L. kaempferi are mainly distributed in Hokkaido and northern Japan, including the Tohoku and Chubu regions (Forestry Agency 2019). The trees of L. kaempferi and hybrids between L. kaempferi and other Larix species have been planted in Japan (Iizuka et al. 2000;Fujimoto et al. 2006a, b;Fukatsu et al. 2015), North America (Cáceres et al. 2018), China (Dong et al. 2019), and Europe (Pâques et al. 2010). This species is one of the target species for tree breeding programs managed by the Forestry Agency in Japan; it is also Page 2 of 15 Takahashi et al. Annals of Forest Science (2023) 80:1 used for breeding materials in many countries (Kurinobu 2005). The tree breeding programs of L. kaempferi in Japan were started in the 1950s, selecting plus trees with superior growth rates and straightness as criteria in artificial and natural forests (Kurinobu 2005). Recently, the selection of second-generation plus trees crossbred by using selected first-generation plus trees has been started to improve growth rate and wood quality as target traits, with plans to establish seed orchards in each prefecture in Japan (Fukatsu et al. 2015).
Since the structural lumber in L. kaempferi is often subjected to bending load, bending properties-including the modulus of elasticity (MOE) and the modulus of rupture (MOR)-are important criteria for assessing wood quality. It has been reported that mechanical properties are highly heritable traits in softwood species (Fujimoto et al. 2006a;Lenz et al. 2010;Chen et al. 2014;Takahashi et al. 2021). For example, Fujimoto et al. (2006a) reported that the heritability values of MOE and MOR in hybrid larch (L. gmelinii × L. kaempferi) were 0.44 and 0.66, respectively. In addition to MOE and MOR, bending work (W)-which is the amount of energy absorbed until the wood is broken-is also important in bending properties because it can be used to evaluate toughness. Static bending properties are calculated from loaddeflection curves obtained from a static bending test. Thus, the shape of the load-deflection curve is important for understanding the elastic and plastic properties of wood, for example, a higher proportional limit showing resistance to deformation by load and the higher maximum load and the longer deflection in the plastic region showing resistance to failure. We previously reported that the type of load-deflection curve obtained in the static bending test of juvenile wood genetically varied among 18 families of 20-year-old Cryptomeria japonica, and the load-deflection curves affected by mating parents could be divided into four types (Takahashi et al. 2021). However, information on the inheritance of mechanical properties, such as static bending properties, is still limited for full-sib families of L. kaempferi, despite being one of the important first steps to be studied for the improvement of wood quality.
Superior trees with higher mechanical properties of wood would be indirectly selected by wood density and microfibril angle (MFA) for the effective selection of trees (Alteyrac et al. 2006;Lenz et al. 2010;Pâques et al. 2010;Chen et al. 2014;Takahashi et al. 2021). Pâques et al. (2010) found higher genetic correlations between wood density and MOE for 16-and 19-year-old hybrid larch (Larix × eurolepis Henry). In 12 trees of 80-yearold Picea mariana, MFA was negatively correlated with MOE (r = −0.78) or MOR (r = −0.53) (Alteyrac et al. 2006). These results suggest that the selection of trees with higher mechanical properties of wood can be achieved by the selection of wood with higher wood density and lower MFA.
For tree breeding of wood quality in L. kaempferi, an accumulation of information about the inheritance of static bending properties is necessary. To clarify the inheritance and relationship with wood properties in static bending properties, it is useful to understand the variation in the shapes of load-deflection curves among families. In the present study, wood properties and bending properties were measured for 15 full-sib families of 36-year-old L. kaempferi trees grown at two progeny test sites located in Gunma and Nagano prefectures, Japan. We aimed to clarify the inheritances of wood properties and radial variations, as well as the relationships between wood properties and bending properties. Furthermore, we tried to classify families by differences in the types of load-deflection curves in the static bending test.

Progeny test sites
Materials were collected from two L. kaempferi progeny test sites (Gunma and Nagano prefectures, located in Central Japan), and two progeny test sites were defined as the Gunma and Nagano sites in the present study. The Gunma site is located 40 km north of the Nagano site ( Figure 5 in Appendix). An outline of these sites is shown in Table 6 in Appendix. The two sites were established by planting the seedlings of 56 full-sib families produced with a full diallel mating design of eight common plus-tree clones without selfing, using a randomized block design with five replicates. Each family was planted in a quadratic plot with 20 trees at each replicate block. Gunma and Nagano sites were planted in 1977 at spacings of 2.2 × 2.2 m and 2.0 × 2.0 m, respectively. No thinning treatment was conducted before sampling for the present study.

Materials
From the diallel crossing of eight plus-tree clones of five replicate blocks, the complete diallel crossing of six plus-tree clones of three replicate blocks was selected for the present study. Fifteen full-sib families were pooled with reciprocal families due to the limited number of remaining trees. A total of 269 and 260 trees were used as samples at the Gunma and Nagano sites, respectively ( Table 1). The stem diameter at 1.2 m above the ground and tree height were measured for each tree at the age of 30. Mean values and standard deviations of stem diameter at 1.2 m above the ground in the Gunma and Nagano sites were 15.4 cm and 15.5 cm, respectively; similarly, those of tree height were 14.0 m and 14.1 m, respectively (Table 2). For all sample trees in Gunma and Nagano sites, 40-cm-long logs were obtained from 1.0 to 1.4 m above the ground in October and November 2013, respectively. The trees were 36 years old. Pith-to-bark radial boards of 30 mm thickness were prepared from the logs. After air-drying the boards, one radial direction of each radial board (from the pith to the bark) was used for the following experiments (Takahashi et al. 2022b).

Wood properties
Strip specimens 10 mm thick were obtained from the radial boards to measure the annual ring width (ARW) and latewood width. Cross-sectional images of strip specimens were captured using a scanner. ARW and latewood width were measured in each annual ring from the pith to the bark sides using an image analysis software, ImageJ (National Institutes of Health, Bethesda, Maryland, USA). Latewood was identified by the color difference from earlywood. Latewood percentage (LWP) was calculated as the proportion of latewood width to ARW in each annual ring.
The MFA of the S 2 layer in latewood tracheids was determined using the iodine method (Senft and Bendtsen 1985). At each site, 90 trees in a replicate block were subjected to measuring the MFA. Small blocks were prepared at the 5th, 10th, 15th, 20th, and 25th annual rings from one radial direction of the pith to the bark in an obtained strip. At each radial position, the MFA of the S 2 layer was measured for 30 latewood tracheids on digital photomicrographs using ImageJ. The mean values were then calculated at each radial position.

Data analysis
The values of all wood properties at each radial position were calculated by averaging the values from 1st to 5th, from 6th to 10th, from 11th to 15th, from 16th to 20th, and from 21st to 36th annual rings from the pith (Figure 7 in Appendix; Tanabe et al. 2014). In addition, the overall mean at all radial positions in bending properties and AD was calculated by the weighted average method using the area based on the annual ring number in the center of each specimen. In L. kaempferi, Shiokura (1982) reported that the boundary between juvenile and mature wood was located at the 11th-19th annual rings from the pith. In the present study, the 1st-20th radial positions and the 21st-36th radial positions were regarded as juvenile and mature wood, respectively. The variance components of each trait were estimated using the restricted maximum likelihood (REML) method using ASReml-R (Butler 2021). The estimation of the breeding value and variance components is expressed in the following linear mixed model (Eq. 3): where Y ijklm is the measurement value of the m th individual of family of the k th and l th parents in the j th block of the i th site, μ is the general mean value, P i is a fixed effect of the i th site, B ij is the fixed effect of the j th block in the i th site, G k and G l are random effects of genetic combining ability (GCA) of k th and l th parents, respectively, S kl is a specific combining ability (SCA) between k th and l th parents, PG ikl is the random interaction effect for the i th site and the GCA of the k th and l th parents, BG ijkl is the random interaction effect for j th block in the i th site and the GCA of the k th and l th parents, and e ijklm is the random residual. Random factors were assumed to be distributed normally, with an expectation of zero. The random effects G k and G l were predicted from the variance of GCA as follows: G k~N (0, σ 2 GCA ) and G l~N (0, , respectively. Because the number of samples in the MFA was limited, the B ij and BG ijlm terms could not be included in Eq. 3 for the MFA. The random factors and breeding values of each mating parent were obtained using an "animal model" of the best linear unbiased prediction (BLUP).
The narrow-sense heritability (h 2 ) of each trait was estimated using Eq. 4: where σ 2 GCA , σ 2 SCA , σ 2 pg , σ 2 bg , and σ 2 e are variance components of GCA, SCA, the interaction of progeny × GCA, the interaction of block × GCA, and the residual, respectively. These estimations were carried out using ASReml-R software (Butler 2021).
The genetic correlation between trait x and trait y (r g(x,y) ) was estimated using Eq. 5: where COV g(x,y) is the covariance of trait x and trait y and σ 2 g(x) and σ 2 g(y) are the additive genetic variances of trait x and trait y, respectively. In addition, the phenotypic correlation between trait x and trait y was estimated based on phenotypic variances.
Principal component analysis (PCA) and cluster analysis were employed to categorize the 15 families. Principal component scores were calculated by a correlation matrix with the four following variables: estimated family mean values in load and deflection at the proportional limit and maximum load and deflection. The estimated family mean for the four variables was calculated by the sum of the general mean value (μ), breeding values in each parent (G k and G l ), and breeding values in each family (S kl ) (Eq. 4) to remove the effects of differences in environmental factors. Using the 1st and 2nd principal component scores from PCA as variables, cluster analysis using the Ward hierarchical clustering algorithm was performed for the categorization of 15 families. The optimal number of clusters was determined using the Jain-Dubes method (Jain and Dubes 1988). These statistical analyses were performed using open-source statistical software R 4.0.3 (R Development Core Team 2020).

Mean values and radial variations of wood properties and bending properties
The mean values of the wood properties and their radial variations at each site are shown in Table 2 and Fig. 1, Page 5 of 15 Takahashi et al. Annals of Forest Science (2023) 80:1 respectively. The mean ARW in the two sites decreased from 1st-5th to 21st-36th radial positions, with a drastic decrease at the 11th-15th radial position (Fig. 1). The mean values of LWP, AD, MOE, MOR, and W increased drastically from 1st-5th to 11th-15th radial positions and then slightly increased or became almost stable toward the outer radial positions (Fig. 1). The AD and bending properties in the Nagano site were shown to have higher values compared with those in the Gunma site, especially in the range from the 6th-10th to the 16th-20th radial positions (Fig. 1). The site effects as fixed effects were significant at 6th-10th position in ARW and LWP, 11th-20th position in AD, 11th-36th position in MOR, 16th-20th position in W, and all positions in MOE.
The mean values of the MFA at the 5th annual ring from the pith showed the highest values in each family, being 16 to 17° (Fig. 2). Then, the mean MFA value rapidly decreased to about 7° toward the 25th annual ring from the pith (Fig. 2). The radial variation of the MFA showed a similar pattern between the two sites (Fig. 2). The mean value of the MFA in all families was 10.6° in the two sites (Table 2).

Heritability
The heritability of ARW ranged from 0.000 at the 6th-10th radial position to 0.008 at the 11th-15th radial position (Table 3). The highest heritability in LWP (h 2 = 0.360), AD (h 2 = 0.459), and MOR (h 2 = 0.503) was obtained in the 21st-36th radial positions among the five radial positions. In the MFA, heritability decreased from the inner position to the outer position, with the highest heritability at the 1st-5th radial positions (h 2 = 0.137). The heritability of MOE and W ranged from 0.000 in the 11th-15th to 0.263 in the 6th-10th radial positions and from 0.023 in the 11th-15th to 0.199 in the 6th-10th radial positions, respectively.

Genetic and phenotypic correlations between AD or MFA and bending properties
Genetic correlations with AD in all bending properties were high at almost all radial positions (Fig. 3). In addition, phenotypic correlations with AD were shown above 0.5 in MOE and MOR at 6th-36th radial positions. On the other hand, the estimated standard errors in the genetic correlations between the MFA and bending properties were larger for most radial positions (Fig. 3). As the exceptions, genetic correlations of MFA were obtained at 1st-5th (r g = 0.890) and 6th-10th (r g = 0.320) radial positions. In all bending properties, phenotypic correlations with MFA were shown in the range of −0.2 to −0.4 at 16th-36th radial positions. Table 4 shows the genetic correlations between the mean at all positions and the mean at each radial position for all wood properties. In ARW and AD, correlations were higher than 0.6 at all radial positions, while high correlations in LWP and bending properties were obtained in mainly 11th-36th radial positions.

Classification of load-deflection curves
The plot of principal components for the 15 families' scores and the loading of principal components in juvenile wood are shown in Fig. 4 and Table 5, respectively. The contributions of 1st and 2nd principal components were 52.0% and 29.1%, respectively, and, similarly, in mature wood 55.8% and 25.8%, respectively (Fig. 4). In both juvenile and mature wood, the 1st and 2nd principal components mainly contributed to loads at the proportional limit and maximum load and deflection at the proportional limit and maximum deflection, respectively (Table 5). Cluster analysis using 1st and 2nd principal components obtained from PCA as variables was conducted to classify the 15 families. Based on the Jain-Debus method (Jain and Dubes 1988), the optimal number of clusters was determined to be three groups in both juvenile and mature wood. The 15 families in juvenile wood were grouped into three groups: group I (1, 2, 3, 6, 7, 8, 9, and 10 in family ID), group II (12 in Family ID), and group III (4, 5, 11, 13, 14, and 15 in Family ID) (Fig. 4). In mature wood, the 15 families were divided into three groups by cluster analysis: group I (2, 4, 5, 11, 12, and 15 in Family ID), group II (1 in Family ID), and group III3 (3, 6, 7, 8, 9, 10, 13, and 14 in Family ID) (Fig. 4).
Typical load-deflection curves for the three groups in juvenile wood and mature wood are shown in Fig. 4. In juvenile wood, typical load-deflection curves differed in maximum load and load at proportional limit among groups, but there was no difference in the amount of deflection. A similar result was shown in mature wood, with a larger difference among the groups than in juvenile wood.

Mean values and radial variations of wood properties and bending properties
Mean values of ARW, LWP, AD, MOE, and MOR in the present study were almost similar to those of other previous studies on larch ( Table 7 in Appendix, Miyajima 1958Miyajima , 1985Kawaguchi et al. 1987;Koizumi et al. 1987;Zhu 2002;Karlman et al. 2005;Koizumi et al. 2005;Cáceres et al. 2018). These radial variations obtained in    the present study were almost similar to those reported by previous studies (Kawaguchi et al. 1987;Leban and Haines 1999;Zhu 2002;Karlman et al. 2005;Koizumi et al. 2005).
In general, the MFA in softwood species rapidly decreases from the pith to around the 20th ring from the pith and then becomes constant (Panshin and de Zeeuw 1980). This tendency is also true for L. kaempferi (Takimoto et al. 2013). The mean values and radial variations of MFA obtained in the present study were almost similar to those of previous studies in L. kaempferi (Takimoto et al. 2013). Because latewood shows a higher density compared to earlywood, a higher LWP results in a higher wood density in softwood (Fukatsu et al. 2015). In the present study, AD and bending properties at the Nagano site were higher in almost all radial positions compared to those at the Gunma site ( Fig. 1), although LWP did not vary among sites at all radial positions. Zamudio et al. (2005) reported that the environmental effect on latewood density was pronounced for 31 open-pollinated families planted in the Pinus radiata site in southern Chili. A similar result was reported in Larix decidua trees located at different elevations and climates (Rozenberg et al. 2020). Thus, differences in AD and bending properties between sites might occur due to differences in latewood density caused by environmental differences between sites.

Radial variations in heritability
In softwood species, wood properties differ between juvenile and mature wood (Shiokura 1982;Cown et al. 1999;Ishiguri et al. 2009;Iki et al. 2010). Therefore, to clarify differences in the inheritance of wood properties between juvenile and mature wood, radial variations in heritability have been investigated by several researchers (Fujimoto et al. 2006a;Kumar et al. 2006;Lenz et al. 2010;Chen et al. 2014). In the present study, the heritability of ARW showed low values throughout the stem (Table 3), suggesting that radial growth rate might be affected by environmental factors such as climatic conditions, soil type, and canopy closure rather than genetic factors. In half-sib families of 20-year-old Picea glauca, the heritability of MFA was almost constant, between 0.25 and 0.30, over the range of cambial age (Lenz et al. 2010). In half-sib families of 21-year-old P. abies, the heritability of MFA increased from the 1st annual ring to the 6th annual ring and then decreased up to the bark side (Chen et al. 2014). Fujimoto et al. (2006a) reported that the heritability values of MOE and MOR at the bark side (h 2 = 0.42 and 0.61, respectively) for full-sib families of hybrid larch (L. gmelinii × L. kaempferi) were higher than those at the pith side (h 2 = 0.28 and 0.49, respectively). The radial trend in the heritability of MFA was similar to that reported for P. abies (Chen et al. 2014). Chen et al. (2014) also reported that the heritability of wood density and MOE increased from the pith to the bark sides. The higher heritability of AD, MOE, and MOR at the outer positions obtained in the present study was in accordance with those of previous studies (Fujimoto et al. 2006b;Lenz et al. 2010;Chen et al. 2014). Based on these results, it is considered that the genetic control of the MFA near the pith is larger than that at the outer radial positions. In addition, AD and bending properties in the 6th-10th radial positions were also relatively strongly genetically affected among juvenile wood positions. Because the highest heritability was obtained, it is concluded that wood properties, such as LWP, AD, and MOR in mature wood, can be effectively improved by selecting individuals.

Relationships between wood properties and bending properties
Many researchers have investigated phenotypic correlations between wood properties (AD, MFA, and others) and mechanical properties, such as bending properties in softwood species (Cown et al. 1999;Alteyrac et al. 2006;Fujimoto et al. 2006a;Kumar et al. 2006;Iki et al. 2010;Chen et al. 2014;Cáceres et al. 2018). For example, Cown et al. (1999) reported that the influence of MFA on MOE (r = −0.76) in 28-year-old Pinus radiata was larger than that of wood density (r = 0.58) in juvenile wood, whereas wood density showed a greater stimulus in mature wood. On the other hand, Iki et al. (2010) reported that in 43-year-old Abies sachalinensis masters, significant correlations between AD and MOE were found at almost all radial positions, while no significant correlations were found between MFA and MOE at almost all radial positions. The results of phenotypic correlations obtained in the present study were similar to those in hybrid larch (Fujimoto et al. 2006a) and P. radiata (Cown et al. 1999). With a few exceptions, correlations of MOE, MOR, and W with AD at most radial positions showed higher values of around 0.5, suggesting that bending properties in L. kaempferi were strongly affected by AD. The influence of MFA on bending properties is limited in outer radial positions (16th-36th).
Genetic correlations can expect the responses of a trait when selection is applied to another trait (Falconer and Mackay 1996). In 30-year-old P. radiata, Kumar et al. (2006) reported that genetic correlations between wood density and static MOE were moderate (r = 0.51) in the core wood zone (the 3rd to 4th annual ring from the pith) but high (r = 0.78) in the outer wood (the 9th to 10th annual ring from the pith). Chen et al. (2014) reported that genetic correlations between MFA and MOE were high negative values, and the correlations between wood In the present study, high genetic correlations were found in AD with MOE and MOR at almost all radial positions. Based on the results, AD can be considered a criterion for improving the bending properties of L. kaempferi.
On the other hand, W at 1st-10th radial positions correlated with MFA. A similar result was found for juvenile wood in C. japonica (Ishiguri et al. 2009). Wood properties as a criterion for selecting trees with superior bending properties should be highly heritable. Therefore, it is suggested that trees with superior bending properties can be effectively selected by the selection of trees using AD as the criterion in L. kaempferi. Fujimoto et al. (2006a) reported that overall means of AD, MOE, and MOR can be estimated by mean values of those in inner wood (pith to 8th annual ring from pith) in hybrid larch (L. gmelinii × L. kaempferi). In ARW, AD, and MFA, higher correlations were obtained in the inner radial positions (Table 4), suggesting that early selection of these properties is possible in L. kaempferi. Based on the higher correlations in LWP and bending properties in outer radial positions (11th-36th) higher than inner positions, early selection for these wood properties is considered desirable after 11 ages.

Inheritance of load-deflection curves in 15 full-sib families
In juvenile wood of C. japonica, we previously investigated the types of load-deflection curves and found that they were divided into four types by the effect of the combinations of mating parents (Takahashi et al. 2021).
Although the load-deflection curves in juvenile wood were not grouped distinctly compared to those in C. japonica, the slight differences in load-deflection curves among groups in juvenile wood of L. kaempferi were found in load at the proportional limit and maximum load (Fig. 4). On the other hand, it was reported that the load-deflection curves of mature wood in Chamaecyparis obtusa largely varied among six families compared to juvenile wood (Takahashi et al. 2022a). Similar results were obtained in the present study (Fig. 4), but there was less difference in the amount of deflection compared with mature wood in C. obtusa (Takahashi et al. 2022a). These results suggest that the variation of load-deflection curves, especially the amount of deflection in L. kaempferi, was smaller in juvenile and mature wood than in C. japonica and C. obtusa. Thus, in L. kaempferi, it is concluded that improving mature wood with higher bending properties while maintaining the characteristics of the materials (higher proportional limit and smaller plastic region) is possible in L. kaempferi by selection in tree breeding programs.

Implementation of wood quality improvement in L. kaempferi by tree breeding
In breeding programs for L. kaempferi in Japan, the selection of second-generation plus trees has been currently conducted from the breeding population in progeny test sites (Kurinobu 2005;Fukatsu et al. 2015). In the results obtained in the present study, AD was genetically strongly affected at almost all radial positions compared with other wood properties. In addition, significant genetic correlations were found between AD and MOE or MOR, especially in the outer radial positions (Fig. 3). Thus, it is concluded that in L. kaempferi, genetic improvement for wood density and bending properties was effective for mature wood compared to juvenile wood, and improvements in wood density resulted in improvement of bending properties, which are important traits for use as structural lumber in L. kaempferi. Leban and Haines (1999) reported that specific MOE (the ratio of MOE and wood density) can be used as a criterion to evaluate the strength performance of wood. In the present study, specific MOE in Nagano site (19.53) was higher value than that in Gunma site (17.74), indicating that wood produced from Nagano site was characterized by higher strength properties per unit weight compared to wood from Gunma site. Further research is needed for the evaluation of the possible application of specific MOE as a selection criterion of the superior tree for structural wood production in tree breeding.

Conclusions
The inheritance of wood properties (i.e., ARW, LWP, AD, and MFA) and bending properties was investigated for 15 full-sib families in 36-year-old L. kaempferi. In almost all wood properties, the mean values and radial variations determined in the present study were similar to those reported in previous studies. From the results of phenotypic and genetic correlations, AD can be used as a criterion by which to select trees with superior bending properties. Furthermore, significant correlations were found between the overall mean and mean values at almost all radial positions for AD, MFA, MOE, MOR, and W. MFA was genetically controlled near the pith. In contrast, the heritability of LWP, AD, and MOR was shown to have the highest values on the outer side. Although the load-deflection curves of 15 families in L. kaempferi could be divided into three groups in both juvenile and mature wood, similar load-deflection curves with slight differences in loading parameters were obtained in all groups for both juvenile and mature wood. Larger differences in maximum load among families were obtained in mature wood compared to juvenile wood, suggesting the possibility of improving mature wood with higher resistance to rupture and maintaining the characteristics of materials (a higher proportional limit and smaller plastic region) in L. kaempferi by selection. However, because the sample trees used in the present study were smalldiameter trees that were not enough size for producing the actual size of structural lumber, further study using full-size structural lumber is necessary for evaluating wood quality and that inheritance in this species. The annual temperature and precipitation were estimated using data of the nearest meteorological station, provided by the Japan Meteorological Agency. Mean annual temperature was calculated by averaging monthly mean temperature obtained from 2008 to 2012. Mean annual precipitation was calculated by averaging total monthly precipitation obtained from 2008 to 2012

Appendix
Bl D Moderately moist black forest soil, B D(d) Moderately moist brown forest soil Table 7 Mean values of wood properties in L. kaempferi reported by several researchers